Loading...
Home > Error Code > Jacuzzi Error Codes

Jacuzzi Error Codes

Contents

Indicates a shorted sensor and the heater is disabled. The J-315 is similar to the J-325 but has more jetting for more water movement. Heater will automatically turn on when this happens and stay in this mode until water temperature reaches 15 degrees below set temperature. Some system status codes are identified below as well, with the phrase "system message, not an error". click site

The heater and jets pumps continue running until the spa unit is out of the danger zone. DO NOT GET INTO THE WATER. The countdown timer for the Change Filterfeature needs to be reset (page 31). The Jacuzzi Spa J-325 hot tub spa is a 3-4 person hot tub.

Jacuzzi Error Code Fl1

Refill, if necessary. If display shows only this message (blinking) spa is shut down. The Jacuzzi Spa J-325 hot tub spa is a 3-4 person hot tub.

The Spa or Hot Tub Panel Displays: dr, dry This indicates that there is not enough water in the heater. Great tub for a small family. Note: A common programming mistake is overlapping filter times that may cause the spa to filter continuously.• Check the water level.• Check the water temperature with an accurate temperature thermometer. Vita Spa Error Codes Contact Jacuzzi hot tubs dealer or a service technician.

ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement Jacuzzi Error Code 616 PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected. For information regarding repairs click here If your spa is not overheating and you are getting the above error codes then a couple of things could be happening. Water temperature has reached 118ºF.

Stands for “Overheat”- and the tub shuts down because water temp is too hot. How To Fix Flo Error Hot Tub Sometimes it will give us little hints as to what is going on. Pictured here is a Balboa® control system used in Belize Spas brand. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 =

Jacuzzi Error Code 616

I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah Inspect these first:• Check slice or ball valves. Jacuzzi Error Code Fl1 The Jacuzzi  J- 575 hot tub spa is a 6 person hot tub. Balboa Hot Tub Error Codes ONLY USE FINGER TIGHTENING METHOD!4.

Contact dealer or a service technician. get redirected here Std = Spa operating in Standard Mode. All Rights Reserved. The fundamental reason is water flow through the spa control system, if the water is not flowing at a rate to satisfy the switch, it will result in one of the Jacuzzi Error Code Cf

Snb = Spa is shut down. Feature not Installed Message displays when you try to activate features that are not installed. No action is needed. http://shpsoftware.com/error-code/it-error-codes.php Open Flow Switch Means that the switch is malfunctioning and staying open, the filter cartridge for the circulation pump is dirty or an air lock issue occurred at the intake for

System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps. Marquis Spa Error Codes Spa has shut down. Power down the spa.

Shut the power down to the hot tub and contact the dealer or service technician if the problem continues. – – – The water temp has raised above acceptable safety limits

  • For further troubleshooting click here.
  • No action is necessary.
  • Please Check Filter Message displays when the reminder time of the filter has expired.
  • Remove your filters.
  • This condition does not kick in until the water temperature climbs to 95°F (35°C).

Raise the water temp settings in order to cancel the Summer Logic condition. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. DO NOT GET INTO THE WATER. Jacuzzi Error Code Fl2 I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct.

No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold. Purchase new UV bulb from dealer and reset countdown timer. The J- 325 features two deep bucket seats and one deep lounge. my review here FL1 = Water flow problem, inhibited or pressure switch malfunction.

Switch spa to Programmable Mode in order to turn the heater on solely during programmedfilter cycles. In both cases, the spa heater will deactivate. Check for dirty or clogged filter cartridge.3. The J- 495 features four deep bucket seats and some good bench seating as well to accommodate all your friends.

The Jacuzzi Spa J-210 hot tub spa is a 6 person hot tub. Join 6 other subscribers Email Address Top Posts & Pages Jacuzzi Hot Tubs Error Codes & Information Hot Tub Filters - When To Clean & When to Replace Beachcomber Hot Tubs Contact dealer or a service technician. Email check failed, please try again Sorry, your blog cannot share posts by email. %d bloggers like this: http://www.spadepot.com/spa-error-codes.htm SpaCyclopedia Contact CHECK OUT 0 Your cart is empty.Continue shopping to add

FL1 or FL2 (Flashing) When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there is an air lock Take off the spa cover to allow the water to cool down.2. You can follow any responses to this entry through the RSS 2.0 feed.

© Copyright 2017 shpsoftware.com. All rights reserved.