Loading...
Home > Error Code > Jacuzzi J 330 Error Codes

Jacuzzi J 330 Error Codes

Contents

Contact the dealer or service technician. A flashing "FL2" display means the flow switch is malfunctioning closed. If problem persists, contact your authorized Jacuzzi dealer. 14.7 panel Flashes Fl1 or Fl2 (spas with Circulation pump option) A flashing "FL1" display means the flow switch is malfunctioning open, the Heater disabled but the spa is operational. http://shpsoftware.com/error-code/jacuzzi-error-codes.php

Normally there's nothing in particular that causes them to go out, they just wear down and quit running. The Jacuzzi hot tubs are split into five categories the Jacuzzi J- LX series, Jacuzzi J-500 series, Jacuzzi J-400 series, Jacuzzi J-300 series, and the Jacuzzi J-200 series. A: This is absolutely the most common error code for a service call. The Jacuzzi Spa J-135 hot tub  is a 6 person entry level hot tub.

Jacuzzi Fl1 Flashing

If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature. Please try the request again. If the circulation pump is not running, turn power off at the main breaker, then turn power back on. See “Summer Log” below.3.

Low speed jets pump 1 and optional circulation pump (if your spa is equipped) activates to circulate water through heater. To print the manual completely, please, download it. Stands for “Overheat”- and the tub shuts down because water temp is too hot. Jacuzzi J 345 Fl1 Error Stereo Receiver Troubleshootingpage 62................................................................................................................................................................

Contact a Jacuzzi hot tubs dealer or a service technician. Jacuzzi Error Codes danwat1234 says: In my case I took apart the hot tub cover and... The Jacuzzi  J- 575 hot tub spa is a 6 person hot tub. OH = High temperature condition, has reached 110ºF.

BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" Jacuzzi Error Code Fl2 Contact the dealer or service technician if the problem continues. Summer Logic “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather. OHH = Overheat.

Jacuzzi Error Codes

Now, if your error code did not go away, you need to determine if you have a bad flow switch, circulation pump, circuit board, or in rare instances a bad topside The J- 470 features four deep bucket seats for the ultimate deep sitting hot tub. Jacuzzi Fl1 Flashing System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps. Jacuzzi Code Cf Snb = Spa is shut down.

The spa is deactivated for potential damage to spa and its components. my review here Ask a helper to turn on water for 30 seconds, then turn off. The system returned: (22) Invalid argument The remote host or network may be down. To clear the message press button D toreturn to the Main Menu Press the D button to clear the message and return to the main menu. Jacuzzi Error Code 616

In some instances it may be more prudent to contact a local repairman or send Spa Care Center your control box for evaluation/repair. Sn2 Stands for “Sensor 2” and displays when the temperature sensor is malfunctioning. Jim Logged widnes Junior Member Posts: 4 Re: J345 FL1 error « Reply #2 on: August 13, 2009, 09:51:51 AM » Hi Jim.Thanks for the quick response.Never thought about economy mode...yung http://shpsoftware.com/error-code/it-error-codes.php Contact the dealer or service technician.

FL1 or FL2 (Flashing) When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there is an air lock Fl1 Error Sundance Spa Your filters were just clogged restricting flow through them. So I took the whole pump out and took it apart completely, motor and all!..

Add water if necessary. 2.

  1. Sensor plugged into jack B is not working.
  2. Feature not Installed Message displays when you try to activate features that are not installed.
  3. The Jacuzzi Spa J-135 has basic jetting making it an entry level hot tub .
  4. If you put the filters back in and FL1 comes back its a bad filter.Are they orignal filters?
  5. Jets pump 1 will likely deactivate, also. 1.
  6. YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART.

Have been looking here for a few years and have found all the information that I have needed with regards to my tub, water quality, etc and thus have never really Shut the power down to the hot tub and contact the dealer or service technician if the problem continues. ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection to 0.0.0.8 failed. Jacuzzi 616 Reset Jet pumps 1 and the heater activate automatically to bring the temp to 15°F (8°C) of the settemps.Note: this condition often occurs when filling the spa with water since tap water

See “Summer Log” below.3. Site by Take 42 Login|Contact Us Pool and Spa Questions about Pool Repair? The Jacuzzi Spa J-135 features two deep bucket seats for the and a lounge. navigate to this website A flashing "FL2" display means the pressure switch is malfunctioning closed.

But however with that being said I am stuck with this hot-tub for now and we do like it when it all works like it should.Anyways, I drained, cleaned and refilled The J-355 has a small but good step to enter the hot tub. Sn1 Stands for “Sensor 1” and displays when the high-limit sensor is malfunctioning. You can find the Jacuzzi J-575 replacement hot tub cover here.

Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = Do not use spa when temperature is flashing or the OH message is displayed. It has disabled itself to prevent further damage. No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold.

It is also helpful sometimes to put your spa in economy mode to prevent overheating in the summer. But after reading this forum about the heat issue others were having with this style and brand I thought well maybe I can fix it myself so I got right to BLB (Flashes in between water temperature and “blb”) Indicates that spa needs a new UV bulb. The J-335 is an entry level hot tub with some great jetting.

Please Check Filter Message displays when the reminder time of the filter has expired. The J- 325 features two deep bucket seats and one deep lounge. Below are some of the more recent Jacuzzi models. The J-585 also has a very good step to enter the hot tub.

Rare system error.

© Copyright 2017 shpsoftware.com. All rights reserved.